All your instructions online, with over 1000 different brands to choose from. We are here to Help you Find the Right Manual for your Vehicle. With Unlimited Downloads, You're Free to Push your Creative Boundaries and Try New Things. All the Creative Assets you Need Under One Subscription!
Loading Dock Levelers — Rice Equipment Co., Loading Dock & Door Service
36K views 7 years ago How to Install an Edge of Dock Leveler 36,041 views 93 Installing your Copperloy Edge of Dock Leveler properly is paramount to ensure loading dock safety, efficiency. Dock Leveler Installation Manual By Rite-Hite RHM & ML-900 Mechanical Dock Leveler part of the SMOOTH TRANSITION DOK SYSTEMTM RHM Shown RHH Hydra-RiteTM / Base & HL-900 Hydraulic Dock Leveler part of the SMOOTH TRANSITION DOK SYSTEMTM RHH Shown RHA & AL-900 Air Powered Dock Leveler part of the SMOOTH TRANSITION DOK SYSTEMTM RHA Shown MADE IN U.S.A. Raise the deck using a lifting support bar, then fasten the ¾" x 10" lifting ring to the ¾" nut at the front of the deck. Using the included maintenance strut, prop open the leveler with the lip extended. Shim underneath the primary lift cylinder ram to increase stiffness in that area. Weld it to secure in place. 5. Never leave loads sitting on the dock leveler. 6. Do not attempt to raise the dock leveler if someone is standing on it. 7. Do not use the dock leveler if the lip's full width is not fully supported by the vehicle load bed. 8. Do not operate the dock leveler beyond its rated capacity. 9. Do not drive or walk onto the truck until it is.
Edge of Dock Levelers (EOD) — Rice Equipment Co., Loading Dock & Door Service
Installation & Service Manual (Version: B) 8 Type XP 1.9 Who is this manual intended for? This manual is intended for installers and service engineers of the dock leveller of type XP. All installers and engineers of the dock leveller must fully read the following chapters and follow the instructions exactly. Our dock levellers comply with BS EN 1398 which specifies the safety requirements for design, construction, installation, maintenance and testing of dock levellers, Dock leveler (US) and for safety components on dock levellers, Dock leveler (US). SWING LIP DOCK LEVELLER View Product TELESCOPIC LIP DOCK LEVELLER View Product MECHANICAL DOCK LEVELLER This User's Manual contains information that you need to safely install, operate, maintain and identify parts for the dock leveler. Please read and follow this User's Manual when installing the dock leveler. You may find safety signal words such as DANGER, WARNING, CAUTION or NOTICE throughout this User's Manual. Their use is explained below: BLUE GIANT SERIES DOCK LEVELERS—INSTALLATION & TECHNICAL MANUAL 17.0 LAMINATED BUMPER INSTALLATION 17.1 WEDGE ANCHORS Quantity Description Part # 1. Mark and position each hole on the dock face. 6" x " 010-108 2. Drill each hole in the concrete using a 5/8" (16mm) or carbide- tipped masonry drill bit.
Dock leveler install YouTube
4.Never attempt to work under the dock leveler without properly securing the front and center sections. 5.Keep clear of dock leveler while in operation. 6. Do not exceed capacity rating. 7.If dock leveler is not operating normally, discontinue use. Request maintenance personnel to inspect and contact your local Bluff dealer if necessary. Grind off any bolts sticking up or hammer away any pieces if concrete that are in the way. You are now ready to install your new dock leveler. Guiding the new unit into the pit. Make sure you have even spacing on the sides. Normally, a dock leveler is 2″ smaller than the pit width, so there is a 1″ gap on either side.
How to install an edge of dock leveler Installing an edge of dock leveler is simple and does not take a lot of time and work. Follow the instructions below to properly install the leveler. Inspect the dock leveler for any types of damages or any missing parts once you receive the unit. use of dock leveler restricted to trained opera tors. 3. al wa ys chock trailer wheels or engage truck rest aint before opera ting dock leveler or beginning 4. never use hands or equipment to move ramp or lip. 5. before activ a ting dock leveler: • ensure trailer is backed up against bumpers. • remove any end load, if required.
Mechanical Dock Leveler Installation Commercial Installation Door Masters Bourbonnais IL
Move all equipment, material or people off dock leveler and store dock leveler at dock level before allowing the vehicle to leave. inSTaLLaTion, MainTenance anD SerVice Place barricades on the dock floor around the dock leveler pit and in the driveway in front of the pit while installing, maintaining or repairing the dock leveler. Dock Leveler installation guide READ AND UNDERSTAND ALL SAFETY PRACTICES AND OPERATING INSTRUCTIONS before installing, servicing or operating the dock leveler.
