GATOR XP G2 is made with a state-of-the-art manufacturing process. Specifically, calibrated sand is mixed with sophisticated intelligent polymers. This new generation of Intelligent Polymers neutralizes haze and dust. The polymeric sand application is now dust free, haze free, no blower needed, requiring only one watering and offering a Rapid. Gator XP G2 is formulated to neutralize haze and dust. It's ideal for concrete pavers, wet cast products, and natural stone with joints up to 4". This new ge.
How To Install Gator XP G2 With Rapid Set Technology YouTube
GATOR XP G2 wordt gemaakt met een ultramodern fabricageproces. Meer specifiek, gekalibreerd zand wordt gemengd met geavanceerde intelligente polymeren. Deze nieuwe generatie intelligente polymeren neutraliseert waas en stof. Het aanbrengen van polymeerzand is nu zonder stof, zonder waas, er is geen blazer nodig, er is maar één besproeiing. Make sure that the surfaces you are bonding together are clean. STEP 2. Cut the spout and puncture a hole in the cartridge with a nail. STEP 3. Using a caulking gun, apply GATOR BLOCK BOND XP LOW VOC polyurethane adhesive on the clean surfaces. STEP 4. Join the two surfaces firmly, use twisting motion. WARRANTY. Sweep off excess GATOR SAND XP G2 from the paved surface, first with a hard-bristle broom, then a soft-bristle broom. Take care to leave the height of GATOR SAND XP G2 at least 3 mm below top of paver's surface or 3 mm below the chamfer 4 Shower for a minimum of 30 seconds for 3 sq. m. or until the GATOR SAND XP G2 repels Since the GATOR BASE panels have a high thermal resistance (it would take nearly 15.7″ (40 cm) of 0-3/4″ (0-20 cm) dry stone, compacted to a porosity of 20% to equal the insulation provided by a single layer of GATOR BASE panels), it can be assumed that there would be better frost protection with the GATOR BASE than with the usual additional 6″ (15 cm) aggregate base.
Gator Sand XP G2 Voegzand Zak 20kg Antraciet bol
Always refer to the latest GATOR MAXX G2 Technical Data Sheet (TDS) at AllianceGator.com before installing GATOR MAXX G2.; Pavers and slabs must be installed according to ICPI Tech Spec #2 traditional base (www.icpi.org) before GATOR MAXX G2 installation. For overlay, ICPI recommends 2″ (5 cm) diameter drainage holes spaced approximately 10 ft (3 m) apart and at the lowest elevations in the. STEP 1. Scarify or rototill at least 1 in (2.5 cm) of the surface, break up any clumps, make any necessary repairs, and add new surface aggregate as needed. STEP 2. Apply GATOR STONE BOND at the rate of 15 sq. ft. (1.4 sq. m.) per gallon (3.78 L); allow liquid to penetrate. STEP 3. POLYMER SAND GATOR XP G2 is a blend of calibrated sand and sophisticated intelligent new generation polymers that eutralize dust and halos, for an extremely clean installation work. Moreover, there's no need to use a blower - smart polymer sand just requires wetting. Gator XP G2 is recommended for various uses: pool areas, patios, driveways, parking lots, sidewalks etc. For the creation of. 6. Save enough space. G2 Intelligent Polymeric Sand should be installed at a minimum of 1/8 inch (3mm) below the edge or chamfer of the paver. The filled and cured polymeric sand joints should never be in direct contact with foot traffic or tires as this will cause erosion to occur. 7.
Gator Sand XP G2 Voegzand Zak 20kg Zwart bol
Alliance Gator Maxx G2 Intelligent Polymeric Sand for Paver and Natural Stone Joints UP to 4"(Diamond Black) 50 Ib Bag . Brand: Alliance. 4.4 4.4 out of 5 stars 36 ratings. Currently unavailable. We don't know when or if this item will be back in stock. Once Gator XP Sand Bond sets, it becomes very firm and locks between the paver joints. This firm bond maintains pavers securely in place, being equally effective on both horizontal and sloped surface. Features * Can be used for paver joints up to a maximum of 1.5″. * Starts to set as soon as water is sprayed. Fast setting.
GATOR MAXX G2 is made with a state-of-the-art manufacturing process. Specifically, calibrated sand is mixed with sophisticated intelligent polymers.. If a polymeric sand is too hard, it can also be too brittle causing cracking from ground movement. Our Gator Maxx and our Gator XP sands are our most resilient. Note: Polymeric sand is intended. STEP 2. Vibrate the GATOR MAXX G2 into the paver joints using a vibratory plate compactor. A rubber pad is recommended. A roller compactor is best for slab installation. Joints sand level, must be at least 1/8″ (3 mm) below top of paver's surface or 1/8″ (3 mm) below the chamfer. It is best to compact in several directions to ensure there.
Gator XP G2 Alliance Quality is our strength
A. Voordat u Gator XP G2 installeert, kijk altijd eerst op AllianceGator.com voor het laatste Technisch Data Sheet (TDS) B. De zijkant en de bovenkant van de stenen moeten droog zijn wanneer u Gator XP G2 installeert. C. Op een waterdoorlatende ondergrond reageert Gator XP G2 binnen 1 uur na bewatering en boven 0ºC. GATOR MAXX G2 INSTALLATION STEPS (FOR A NEW PAVER SURFACE) 1 Spread GATOR MAXX G2 with hard-bristle broom. Make sure the GATOR MAXX G2 completely fills the joints. Do not use with other materials in the joints. Leave a layer of GATOR MAXX G2 on the surface to aid in the vibrating and consolidation of GATOR MAXX G2 into joints. For textured or.
